Free 2014 Latest Cisco 200-120 Dump (31-40) Download!

QUESTION 31
Three switches are connected to one another via trunk ports. Assuming the default switch configuration, which switch is elected as the root bridge for the spanning-tree instance of VLAN 1?

A.    the switch with the highest MAC address
B.    the switch with the lowest MAC address
C.    the switch with the highest IP address
D.    the switch with the lowest IP address

Answer: B
Explanation:
Each switch in your network will have a Bridge ID Priority value, more commonly referred to as a BID. This BID is a combination of a default priority value and the switch’s MAC address, with the priority value listed first. The lowest BID will win the election process.
For example, if a Cisco switch has the default priority value of 32,768 and a MAC address of 11- 22-33-44-55-66, the BID would be 32768:11-22-33-44-55-66. Therefore, if the switch priority is left at the default, the MAC address is the deciding factor in the root bridge election.

QUESTION 32
What are three advantages of VLANs? (Choose three.)

A.    VLANs establish broadcast domains in switched networks.
B.    VLANs utilize packet filtering to enhance network security.
C.    VLANs provide a method of conserving IP addresses in large networks.
D.    VLANs provide a low-latency internetworking alternative to routed networks.
E.    VLANs allow access to network services based on department, not physical location.
F.    VLANs can greatly simplify adding, moving, or changing hosts on the network.

Answer: AEF
Explanation:
VLAN technology is often used in practice, because it can better control layer2 broadcast to improve network security. This makes network more flexible and scalable. Packet filtering is a function of firewall instead of VLAN.

QUESTION 33
Which two benefits are provided by using a hierarchical addressing network addressing scheme? (Choose two.)

A.    reduces routing table entries
B.    auto-negotiation of media rates
C.    efficient utilization of MAC addresses
D.    dedicated communications between devices
E.    ease of management and troubleshooting

Answer: AE
Explanation:
Here are some of the benefits of hierarchical addressing:
Reference: http://www.ciscopress.com/articles/article.asp?p=174107

QUESTION 34
What is the alternative notation for the IPv6 address B514:82C3:0000:0000:0029:EC7A:0000:EC72?

A.    B514 : 82C3 : 0029 : EC7A : EC72
B.    B514 : 82C3 :: 0029 : EC7A : EC72
C.    B514 : 82C3 : 0029 :: EC7A : 0000 : EC72
D.    B514 : 82C3 :: 0029 : EC7A : 0 : EC72

Answer: D
Explanation:
There are two ways that an IPv6 address can be additionally compressed: compressing leading
zeros and substituting a group of consecutive zeros with a single double colon (::). Both of these can be used in any number of combinations to notate the same address. It is important to note that the double colon (::) can only be used once within a single IPv6 address notation. So, the extra 0’s can only be compressed once.

QUESTION 35
Which two statements describe characteristics of IPv6 unicast addressing? (Choose two.)

A.    Global addresses start with 2000::/3.
B.    Link-local addresses start with FE00:/12.
C.    Link-local addresses start with FF00::/10.
D.    There is only one loopback address and it is ::1.
E.    If a global address is assigned to an interface, then that is the only allowable address for the interface.

Answer: AD
Explanation:
Below is the list of common kinds of IPv6 addresses:
QUESTION 36
The network administrator has been asked to give reasons for moving from IPv4 to IPv6. What are two valid reasons for adopting IPv6 over IPv4? (Choose two.)

A.    no broadcast
B.    change of source address in the IPv6 header
C.    change of destination address in the IPv6 header
D.    Telnet access does not require a password
E.    autoconfiguration
F.    NAT

Answer: AE
Explanation:
IPv6 does not use broadcasts, and autoconfiguration is a feature of IPV6 that allows for hosts to automatically obtain an IPv6 address.

QUESTION 37
An administrator must assign static IP addresses to the servers in a network. For network 192.168.20.24/29, the router is assigned the first usable host address while the sales server is given the last usable host address. Which of the following should be entered into the IP properties box for the sales server?

A.    IP address: 192.168.20.14
Subnet Mask: 255.255.255.248
Default Gateway: 192.168.20.9
B.    IP address: 192.168.20.254
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.20.1
C.    IP address: 192.168.20.30
Subnet Mask: 255.255.255.248
Default Gateway: 192.168.20.25
D.    IP address: 192.168.20.30
Subnet Mask: 255.255.255.240
Default Gateway: 192.168.20.17
E.    IP address: 192.168.20.30
Subnet Mask: 255.255.255.240
Default Gateway: 192.168.20.25

Answer: C
Explanation:
For the 192.168.20.24/29 network, the usable hosts are 192.168.24.25 (router) ?192.168.24.30 (used for the sales server).

QUESTION 38
Which subnet mask would be appropriate for a network address range to be subnetted for up to eight LANs, with each LAN containing 5 to 26 hosts?

A.    0.0.0.240
B.    255.255.255.252
C.    255.255.255.0
D.    255.255.255.224
E.    255.255.255.240

Answer: D
Explanation:
For a class C network, a mask of 255.255.255.224 will allow for up to 8 networks with 32 IP addresses each (30 usable).

QUESTION 39
How many bits are contained in each field of an IPv6 address?

A.    24
B.    4
C.    8
D.    16

Answer: D
Explanation:
An IPv6 address is represented as eight groups of four hexadecimal digits, each group representing 16 bits (two octets). The groups are separated by colons (:). An example of an IPv6 address is 2001:0db8:85a3:0000:0000:8a2e:0370:7334.

QUESTION 40
What are three approaches that are used when migrating from an IPv4 addressing scheme to an IPv6 scheme. (Choose three.)

A.    enable dual-stack routing
B.    configure IPv6 directly
C.    configure IPv4 tunnels between IPv6 islands
D.    use proxying and translation to translate IPv6 packets into IPv4 packets
E.    statically map IPv4 addresses to IPv6 addresses
F.    use DHCPv6 to map IPv4 addresses to IPv6 addresses

Answer: ACD
Explanation:
Several methods are used terms of migration including tunneling, translators, and dual stack. Tunnels are used to carry one protocol inside another, while translators simply translate IPv6 packets into IPv4 packets. Dual stack uses a combination of both native IPv4 and IPv6. With dual stack, devices are able to run IPv4 and IPv6 together and if IPv6 communication is possible that is the preferred protocol. Hosts can simultaneously reach IPv4 and IPv6 content.

If you want to pass the Cisco 200-120 Exam sucessfully, recommend to read latest Cisco 200-120 Dump full version.

clip_image001