[2017-Oct.-New]300-370 115Q VCE Dumps Free Provided By Braindump2go for Free Downloading[33-45]
2017 Oct. New 300-370 Exam Dumps with PDF and VCE Free Updated Today! Following are some new 300-370 Questions:
1.|2017 New 300-370 Exam Dumps (PDF & VCE) 115Q&As Download:
https://www.braindump2go.com/300-370.html
2.|2017 New 300-370 Exam Questions & Answers Download:
https://drive.google.com/drive/folders/0B75b5xYLjSSNdGVBOXFERG9OSFU?usp=sharing
QUESTION 33
A WLAN was installed at a high AP density. DTPC is lowering the transmit power of many APs too low. Which change m the DTPC transmit power threshold must be made to allow APs to globally increase AP transmit power by 3dBm?
A. from 70 dBm to 73 dBm
B. from -70 dBm to -73 dBm
C. from 70 dBm to 67 dBm
D. from -70 dBm to -67 dBm
Answer: D
QUESTION 34
A user reports being unable to connect to a server with a certain program while connected to wireless. Wh.ch troubleshooting methodology can be used to begin the troubleshooting process?
A. top-down
B. shoot from the hip
C. follow the path
D. bottom-up
E. divide and conquer
Answer: A
QUESTION 35
A client is failing EAP authentication and a debug shows that the server is sending an Access-Reject message. Which action must you take to resolve authentication?
A. Verify that the Validate server certificate on the client is disabled.
B. Verify that the client certificates are from the proper CA and server certificate.
C. Verify that the client server certificate has the proper Windows OlDs.
D. Verify that the user account is the same in the client certificate.
E. Verify that the user is using the same password that is on the server
Answer: B
QUESTION 36
When implementing interface groups, how are the IP addresses sourced via DHCP for wireless clients?
A. through the primary interface of the group
B. through round robin between interfaces
C. through interface group definition
D. through the interface receiving the first response
Answer: B
QUESTION 37
Which three steps would a network engineer use to troubleshoot an AP join problem? (Choose three.)
A. Validate the STP configuration.
B. Verify the ping AP from the controller.
C. Verify the ping AP from the client.
D. Verify that the AP is getting an address from the DHCP server.
E. I Validate the SNMP configuration.
F. Verify the authentication configuration parameters.
Answer: ABF
QUESTION 38
An engineer has run the debug dhcp packet enable command on the wireless LAN controller CLI. Which field contacts the IP address offered to the client?
A. siaddr
B. ciaddr
C. chaddr
D. yiaddr
E. giaddr
Answer: C
QUESTION 39
Refer to the exhibit. Access points ate deployed in an office building and users report that the real-time communications quality of experience is poor when users walk between the elevators The elevators are a heavy metallic obstacle, and AP 3 was installed to cover the elevator area, which AP t and AP 2 signal does not reach Communications are captured for a user walking from point A to point C. and it is observed that the user iPhone device suddenly scans all bands and then roams from AP I to AP 3 somewhere between points B and C WLAN is set to 5 GHz only. Open, default rate configuration.
Which action improves the real-time application quality of experience in this area?
A. Enable 802 11v on the WLAN
B. Enable 802 11r on the WLAN
C. Enable 802 11k on the WLAN
D. Move AP 2 to point B
Answer: B
QUESTION 40
A mobile workstation in a factory contains an AP that is configured as a workgroup bridge.
When the workstation moves, it loses connectivity and disrupts operation.
What can the engineer implement to minimize roaming problems?
A. Use 802.1X authentication.
B. Use Cisco Centralized Key Management for fast roaming.
C. Use AES for encryption.
D. Use the mobile station command.
Answer: D
QUESTION 41
Refer to the exhibit. A new wireless deployment with high AP density is experiencing high latency and connectivity issues on the 24 GHz band, despite an initial site survey done by a certified partner. Which option is the most impactful change a wireless consultant recommends?
A. Increase the fragmentation threshold to allow larger packets over the air.
B. Reduce the beacon period because it reduces the RF interference.
C. Disable lower data rate, such as 1 Mbps and 2 Mbps.
D. Disable the short preamble.
E. Disable 80211g support to reduce interference.
Answer: C
QUESTION 42
An engineer is concerned about rogue-on-wire and wants to enable port security. Which guideline must the engineer follow?
A. Configure Switched Port Analyzer destination ports as secure.
B. Use 802 1x with port security to prevent MAC spoofing.
C. Enable port security on dynamic access ports.
D. Employ static MAC address configuration for APs with port security.
Answer: A
QUESTION 43
An alarm is reporting that one of four ports of a lag group have gone down on a wireless LAN controller. Which troubleshooting methodology can be used to begin the troubleshooting process?
A. shoot from the hip
B. bottom-up
C. top-down
D. follow the path
E. divide and conquer
Answer: B
QUESTION 44
Which ports require unrestricted port access for CleanAir RF spectrum analysis between the AP and Cisco Spectrum Expert?
A. UDP 5246 and 5247
B. UDP 37540 and 37550
C. TCP 16113 and 16114
D. TCP 37540 and 37550
E. TCP 5246 and 5247
F. UDP 16113and 16114
Answer: D
QUESTION 45
Refer to the exhibit. A client reports being unable to log into the wireless network, which uses PEAPv2. Which two issues appear in the output? (Choose two)
A. The AP has the incorrect RADIUS server address
B. There is a problem with the client supplicant
C. The AP has lost IP connectivity to the authentication server
D. The authentic at ion server is misconfigured on the controller
E. The EAP client timeout value should be increased
F. The authentication server is misconfigured in the WLAN
Answer: AE
!!!RECOMMEND!!!
1.|2017 New 300-370 Exam Dumps (PDF & VCE) 115Q&As Download:
https://www.braindump2go.com/300-370.html
2.|2017 New 300-370 Study Guide Video:
https://youtu.be/1BiSQSxOLpQ